PRODUCTS
Explore our Products
Discover a comprehensive selection of cutting-edge equipment and solutions tailored to meet diverse industry needs. Browse our featured products or filter by industry, category, or manufacturer to find the perfect fit for your business.
Featured Products
28ET Application: For general mounting factory Dehumidifier Cabinet Key Features Door opening/closing frequency: Once every 20-40 minutes Compliant to ESD-IEC61340-5-1...
AB-2012 FPS Abrasion Tester can perform tests by controlling tangential force between the test piece and the abrasive wheel in...
The SAT-500 Salt Analyzer from DKK-TOA Corporation is designed for precise and efficient salinity (chloride concentration) measurements, making it an...
Laboratory Testing Equipment
RTM Friction Tester (MODEL FR-7225)
Constant Stress/Strain Fatigue Tester (Series FT-3130)
FPS Abrasion Tester Ueshima UNICORN II Tensile Tester Model TS-2633/TS-2643 Viscoelasticity Analyzer (DMA) Electronics MFG Equipment
Malcom Viscometers: PCU-285
Unitech PCB Cleaners: UC-250M
Malcom Paste Mixers: SPS Series Solder Paste Mixer
Malcom Viscometers: PCU-02V Small Sample
Malcom Wetting Tester: SWB-2
Malcom Paste Mixers: SPS-3000 Solder Paste Mixer Multipoint Fluxer/Soldering: Fluxer 
Eightech Reflow System: N2 Reflow System
Multipoint Fluxer/Soldering: Solbot-II
Sayaka PCB Router: Table Top SAM-CT23Q & SAM-CT35Q Eightech Reflow System: Vacuum Reflow System 
Eightech Reflow System: Air Reflow System
Sayaka PCB Router: Table Top with On-Line Color Camera SAM-CT23S
Rubber & Tire Testing
Outline RTM Friction Tester enables to evaluate friction characteristics of tire tread compound in Dry, Wet and Ice conditions. Friction...
FT-3130 series constant stress/strain fatigue tester counts number of strokes until the test piece is broken.A test is done for...
AB-2012 FPS Abrasion Tester can perform tests by controlling tangential force between the test piece and the abrasive wheel in...
Ueshima UNICORN II Tensile Tester Model TS-2633/TS-2643
VR-7130 Automatic DMA was designed to eliminate possible causes of measurement errors and variability by adopting the full automatic system...
Process Control Equipment
Malcom’s new flagship viscometer replaces the PCU-205 as the industry standard for testing solder paste viscosity. Updates featured in this...
Features: UC-250 Series, from Citizen's established precision and machining technology, is specially designed for SMT line use. Able to clean...
Unlike hand mixing, the Malcom SPS Solder Paste Mixer is a non contaminating mixer which utilizes pseudo planetary motion to...
For fast and easy spot viscosity readings, look no further than the Malcom PCU-02V. This small and compact viscometer uses...
Wetting Balance Tester for through-hole component leads. The Malcom SWB-2 Wetting Balance Tester is an automated solution for measuring the...
The Malcom SPS-3000 Solder Paste Mixer is a addition to the SPS line. This new version adds a number of...
SMT Products
Key Features Multipoint Spray Fluxer Maximum PCB size: 260mm x 340mm Maximum coating area: 240mm x 320mm Maximum number of...
Main Characteristics Eightech’s new NJ08 Series N2 Reflow Oven has pushed the limits of optimal cost/performance. Eco-friendly ultra low power...
Multipoint Soldering System Uses customized and dedicated fixtures/nozzles which eliminates the use of masking tape Lead-free compatible The number of...
Key Features Solution for stress free depanelization Fixture-based highly efficient dust vacuum system Clean and precise depanelization for densely populated...
Characteristics Eightech’s new RV Series vacuum oven has pushed the limits of optimal cost/performance. Significantly decreased the void With combine...
Eightech’s new AJ08M Series AIr Reflow Oven has pushed the limits of optimal cost/performance. Features: Low cost. Low power results...
A PCB Router Machine is often used in manufacturing to separate PCB's with a programmable controller. PCB Router Separator typically...